Easy and Secure Tips: How to Clean a Hand Saw

Nothing is more annoying than seeing rust or corrosion on your hand saw or gardening equipment. We tend to think that rusted items need to be thrown away. However, there are simple but effective ways that can bring them back to life.

Do you believe cleaning a rusty, used, and old hand saw maintenance or restoration process can be pretty an effortless task? You can do this entire process easily in just an hour or even fewer.

First, you need to take some basic cleaning materials, such as:

For a Clean Hand Saw Blade:

  • Newspaper
  • Boiled linseed oil
  • Metal scraper
  • Paste wax
  • Sandpaper (Wet or dry)
  • Razor Blade Scraper
  • Cotton rags or Shop Towels
  • Simple liquid cleaner in a spray bottle

Materials For Cleaning The Saw Nuts:

  • Laundry detergent
  • Brass Brush

Materials For Restoring The Saw Handle:

  • Mineral spirits
  • Boiled Linseed Oil
  • Pocket knife
  • Oil
  • Sand Paper: 120, 150, 220 grit
  • Citrus Strip chemical stripper
  • Steel wool
  • Plastic Scraper (Don’t damage the wood)

Yes, are you prepared with these items? If so, let’s get going and move on to clean a rusty saw blade. If you really deserve to complete restoration in a safe manner, apply with both alert and carefulness.

Alert:

  • The rags can blow up into flame if left to dry in a stack on your floor after being soaked in boiled linseed oil. Rags soaked in boiled linseed oil should leave outside from your house when your work is finished.
  • When dry properly, throw it out in the trash. In a similar streak, mineral spirits are flammable as well. 
  • When utilizing it for cleaning a hand saw, keep the smog outside from an open blaze (as your hot water heater or gas-fired boiler).
  • When finished work by the rags flooded in mineral spirits, never leave those in your shop or house. Please place them in a container and keep them away from your living area. 
  • However, vintage Saws don’t assume any responsibility for damage caused by combustible materials.
  • Seriously, keep the mineral spirits away from children as they are flammable and can cause neurological damage.
  • Lastly, cleaning a rusty or old hand saw is chaotic work. Always wear a couple of solvent-resistant gloves and a mask to protect you from a little accident.

By adhering to these few rules, you will be able to clean out your hand saw without any accident.

The Process To Restore An Old Rusty Hand Saw

Most of this type of work should be performed in a well-ventilated, messy area, such as the garage or on a portable workbench. At first, take out the screws from your hand saw by a correctly fitting screwdriver.

Dismantling The Saw Handle And Plate

  1. With a large flat-head screwdriver, unlatch the screw nuts. Spray a little WD-40 to loosen nuts if they are grappled and wait at least 5 minutes. Then try again.
  2. Use a small screwdriver or hammer and punch to tap out the handsaw nuts gently. Keep carefully aside the screw and saw nuts.
  3. Attentively slither the hand of the saw plate.

How To Clean And Remove Rust From The Saw Blade?

NOTE: I STRONGLY advise you do not use citric acid, vinegar, or evapo to remove the stain from a saw blade. Doing this step can leave pits, dark finish, or remove the main engraving. Maybe attempting to remove rust manually takes about the same time (or less), but the outcome is a nice-looking saw.

Razor Blade Scraper For Hard Parts

This idea is helpful for old rust and saves your sand paper a bit. There is no possibility to leave the track on the saw plate if you file the corners of the razor blade. Drop the dirt into a bag when you reach the blade’s toe and do the same procedure on the opposite side.

Mineral Spirits

After removing loose dirt and rust from the blade, use mineral spirits to clean it. You can use a blank old hot sauce bottle. This permits just the exact amount of mineral spirits to apply to the saw blade. Obviously, you may do this outside for safety. If it is not possible to do this, wear out a respirator-designed outfit to oust natural substances from the breathing atmosphere.

Sand Paper

Apply a simple liquid cleanser to lubricate the blade as you want. This technique keeps away sand paper from clogging, and the rust is imaginably wiped up with the paper towels.

Scotch Brite Pad With Simple Cleanser:

This method will remove much more grime, and dirt from the grooves from the hand saw blade where the sand paper can’t move.

Apply Metal Polish On The Saw Blade

Buff with a cotton cloth or soft towel after applying metal polish. It’s very useful for remove hard rust.

Paste Wax To Coating:

This system will help you prevent future corrosion if you cover it with paste wax. Use a coat of paste wax so the blade doesn’t harm again by rust. After applying both sides properly, let dry for about 10 minutes. So there is possible to protect further rusting and cut much more smoothly. Finally, with a clean rag, buffs off the excess wax. Press hard and forcefully to take off all the extra pest wax.

As An Extra Tip

This method is much easier when you utilize a hard rubber block to hold the sand paper. Be very careful in this step; you may lose the etching if you aggressively sand the blade.

NOTE: Formerly, the hand saw plate has been removing all rust and old stain; apply some soft paper towels to wipe away the majority of the dust and mineral spirits as well. You can use up a regular bounty towel or cloth, but it must be soft. Repeat this previous step on the opposite side of the saw blade and rest the blade aside for perfectly dry.

How To Clean And Refinish A Wooden Saw Handle?

Next, it’s the moment to clean the hand saw handle. Usually, dirt builds up at the hole in the handle where the blade goes. Refinishing a handsaw handle can be done in various ways. Every way follows the same goal to remove varnish. Although there are several ways to take off the varnish, you can choose one based on the type of saw handles.

Remove Old Varnish First

A chemical stripper is required to remove the varnish from saw handles with leaf carvings. The detail of this sort is heating the handle to scrape it off or scrape it off using a pocket knife. There isn’t another technique to get varnish out of those tiny notches.

Boiled Linseed Oil

Apply a little quantity of boiled linseed oil, make certain it’s not only linseed oil. Basically, regular linseed oil takes more time to dry. Ensure all outside parts are coated with boiled linseed oil. Repeat these opposite sides place a warm space to dry up for a minimum of an hour. With a fresh dry rag, remove the excess oil. The saw handle is still a little wet now but in one day or two will be waterless perfectly.

Reassemble The Hand Saw

Presently reverse the steps you took to disassemble the saw. In general, dirt accumulates where the blade goes in the handle. Make sure the medallion screw is properly positioned before you reassemble the handle and blade.

Be careful when installing the nuts because they are very important for a saw. Take care; you have to fit in the entire process properly. Do not be over-aggressive on saw nuts. Get them cozy as well. If they loosen up again after use, just re- tightens up them.

How To Clean Saw Nuts And Saw Screws?

  1. Mix up laundry detergent well and water, then soak the saw nuts in 1:4 solutions overnight.
  2. Drench them for at least 8 hours, and this process will loosen up maximum dirt and grime.
  3. Scrub the hand saw nuts with a brass bristled brush, then gloss with steel wool.

Some Better Stages of Hand Saw Maintenance and Sharpening

Handsaws can efficiently and quickly cut wood across the grain better than other engine-less tools. However, no matter if that saw is a buck saw, bow saw, or pruning saw, metallic teeth can also bite out of the sawyer. These valuable steps should keep your saw in high-class form.

Keep The Hand Saw Dry

It is a good decision to store the saw in a toolbox or carefully keep it in a dry place. A dry system ensures that it won’t touch the water and will be free of rust and other types of moisture.

Greasing The Hand Saw

You must lubricate the saw with the pest wax, gun oil, or WD-40 before storing or after use. Although you use WD-40 or gun oil to remove the stain with a towel, pest wax can probably stay a few times before fully cleaning it.

Don’t Forget About The Handle; Use Oil

If your hand saw handle is made of wood especially, so needs usual lubing. You can prevent dirt and moisture from accumulating with a little linseed oil. Anyway, be sure to clean the groove and the handle rust. Then, you can use sandpaper or steel wool to sand the rough surface and throw out the stains.

Apply A Razor To Remove Blade Rust

Get rid of the handle and position the blade on a flat area. Then, start scraping the saw blade with a razor blade scraper; after this, you can use sandpaper or steel wool. Finally, be sure before using wax or oil, let it dry perfectly. Yes, the next step is to sharpen and set the hand saw correctly.

Sharpen Your Hand Saw Regularly

For beginners, sharpening the hand saw can be a difficult task. Follow the trouble-free step below, and the process will be more easier.

  • Keep an eye on each tooth level, task down the saw, count the keen and start to sharpen as you naturally do the knife.
  • Make certain the saws-all teeth are the same size; if not, file the longest tooth.
  • Overlook dents, if any chipped teeth or rusty teeth. Ensure they are all about 0.5 mm shorter than the indentations.
  • Check out seriously if your blade has crooked teeth and attempt to back to the previous blade term.

You can use your hand saw for a longer time if you keep the points mentioned above while maintaining and fixing it.

10 Hands Saw Safety Tips

Extensively, hand saws are used for many purposes in homes and industries. Now the problem is that there is always a possibility of injury and accident when incorrectly used. Follow up the safety tips below when you’re applying a hand saw.

Make Sure You Are Wearing A Safety Mask And Goggles:

When you’re working with a hand saw, there is continuously a risk of waste flying. To secure your eyes and face, you must wear out eye protection and a safety mask.

Use The Right Size Of Tools

Naturally, hand saws are available in various capabilities and sizes. Ensure to take the right size hand saw and avoid applying too small or too big one.

Before Using Inspect Hand Saw

Be confirm the hand saw is free from damage before using it. The hand saw must not be used in case of loose handles, bent or broken blades, or lost teeth.

Examine Material For Nails Or Knots

Metal pieces, nails, knots, and screws may damage the saw blade. Hand saws can also buckle due to this condition, which can lead to serious injury.

Never Test Sharpness with Hands

Don’t use any part of your body or hand to test the saw’s sharpness.

Start Slowly

You must all-time start cutting slowly to prevent rebound and bucking.

Keep the Material Firmly In Place

Holding the stock firmly in place is crucial to avoid serious injury. When the object is particularly heavy or large, a clamp or vise is necessary.

Always Clean the Hand Saw

To operate hand saw properly and longer period, it would be best if you cleaned it before and after using.

Store In A Safe Place

Hand saws need to be stored in a risk-free, enclosed place to keep them away from children and the wrong people.

Keep Your Arms Far from Your Body For Full-Length Strokes

To get a better outcome and more stability at each stroke, push the hand saw the full length of the blade. When using the saw, keep a safe, comfortable space from your body.

Conclusion

Yes, it is very important to add a protective coating to the iron after the rust has been removed, regardless of how the rust is removed. When you finish all steps perfectly, everyone will think your hand saw is new. However, the good news is; you have been converted an unusable saw to a new and useful to work.

Leave a Comment